How to make a homemade ATV?

The walk-behind tractor is an assistant in cultivating the soil, transporting goods, and harvesting crops. For these manipulations it must be equipped with additional attachments. But in the store they are expensive; a complete set is more expensive than the walk-behind tractor itself. Many craftsmen design and make homemade products for walk-behind tractors with their own hands. Articles, photos, and instructions from the Internet help with this.

Having the simplest skills in working with an angle grinder, a welding machine, or a drill, you can assemble useful homemade products from scrap materials and disused parts. Homemade structures are often made of stronger metal than purchased ones and last longer.

Homemade devices for walk-behind tractor

The necessary attachments on the farm include:

land cultivators - plows, cutters, rippers;
for crop care - hillers;
rake;
snow shovels;
seeders, planting devices.

Rake for walk-behind tractor

Homemade rakes for a walk-behind tractor are used when preparing hay for livestock on a small farm. They are made by hand from narrow metal pipes and rods. To create a durable structure, the parts are assembled for welding.

Homemade rakes are foldable for easy transportation.

By designing the rake yourself, you can make the grip width at your discretion. The pick-up height of the rolls is adjustable. Rake rods are made for collecting hay or mown grass on the site. In the second case, both the width of the structure and the size of the teeth can be reduced.

Homemade crow's feet cutters for walk-behind tractor

Crow's feet cutters help to deeply loosen the soil and crush large clods of earth.

This device is a one-piece welded structure, so it is stronger and more durable than conventional walk-behind cultivators. The cutter qualitatively processes hard soil for sowing potatoes. It can be used to plow the ground under the snow.

The quality of plowing depends on the degree of sharpening of homemade cutters. The soil becomes lush and rises 5-10 cm if the edges of the flat cutters are sharp. They crush large and small roots, destroy harmful beetles and wireworms, and saturate the soil with oxygen.

Homemade “crow’s feet” for a standard input mount must be made with a diameter of 52 cm, a gripper of 1.25 m, and a number of beams of 30 pieces. Each beam is bolted to the coil.

Homemade plow

A homemade plow for plowing is easy to make even for a person with minimal skills in working with metal. Milling cutters are used to loosen already used soil. The plow is used to cultivate virgin soil and compacted hard soil. It has a greater margin of safety. The plow is expensive, not every summer resident can buy it, but you can try to make it yourself.

You will need a plate 4-5 mm thick and a pipe with a wall of the same thickness. The structure is attached to the frame. The main element of the device is a sharpened plate; it must be cut with a grinder in the shape of a blade. The ploughshare has the shape of an elongated flat trapezoid. We fix the pipe and assemble the structure completely. It is connected to the walk-behind tractor via a hitch.

Reversible plow

The plow of this design is a little more complicated. A rounded feather is attached to the top of the homemade product. Not only the land is plowed, but also the cut layer is dumped - when processing virgin soil, this is sometimes necessary. The complex structure of a reversible plow requires its manufacture by a professional craftsman who can calculate the exact parameters of each part.

One of the varieties of such structures is the Zykov plow. To assemble it yourself, you will need a stand with which it clings to the walk-behind tractor, the plow body itself with the ploughshare, a board for support and a curved blade for turning over the layers. The plow moldboard is made of a pipe with a diameter of 50 cm.

Blade-shovel

A walk-behind tractor can be used to level land plots for the construction of utility structures. Like a bulldozer, it can clear sidewalks and paths of dirt and snowdrifts. To make a homemade blade, you need to take a metal sheet 2 mm thick. For strength, plates of thicker metal are welded vertically inside the blade - they will not allow the rear wall of the blade to sag. You also need the lower part of the shovel; it is lined with tin so that the bottom does not get stuck in the ground or snow. The bottom of the shovel is placed at a right angle to the lower base.

Homemade products for a walk-behind tractor can be made with your own hands from used materials.

To make a homemade shovel you will need a metal saw, a drill and a welding machine. A 200-liter steel barrel is suitable as a material. It must be cut along the height into 3 parts and the outer two of them welded together. The metal of the barrel is thick enough to make the device durable.

Potato planter

A very popular and indispensable piece of equipment in the garden is a homemade potato planter. It has a tuber expander with a hole at the bottom and disks for burying them in the ground. The rear wheel on the inside must be covered with a plate so that the planting material does not fall under the wheel of the walk-behind tractor. The entire structure is mounted on a steel frame. The depth of its fixation is adjustable.

Trencher operation

The executive body - a bar with two soil-cutting cutters - is installed on the front suspension of the walk-behind tractor. The depth of the recess is regulated by a ratchet mechanism for fixing the angle of the bar.

The unit is combined with the front hitch of the walk-behind tractor. Excavation of destroyed soil is carried out with a dump shovel on the standard rear suspension of the walk-behind tractor.

The power unit of the walk-behind tractor and the hydraulic system of the attachment are started.
The transmission of torque to the road wheels is disabled.
The cutter's gyromotor starts, the cutting discs begin to rotate and form a trench cut.
The chassis drive is turned on and the walk-behind tractor begins to move.
The dump shovel delivers the destroyed soil to the edge of the trench.

Cutting discs and chain drives are necessarily protected by protective covers.

Special equipment is used to dig trenches for private or industrial purposes. A trencher for a walk-behind tractor is a replaceable mechanism that allows you to dig a trench of any size for laying underground highways, electrical networks, communications, pipes, and can also be used for other purposes.

The trencher (bara) can be attached to a walk-behind tractor and is intended for:

digging ditches and holes;
removal of already unusable road surfaces;
soil cutting;
preparing the land for planting;
carrying out loosening work;
land reclamation;
works with pouring the foundation;
drainage.

Friends, today I will tell you how to make a dragon with your own hands. | Topic author: Inna

Friends, today I will tell you how to make a dragon with your own hands.

Necessary materials. 1. Wire of different thicknesses (1.6mm and 0.88mm); 2. Foil; 3. Masking tape; 4. Putty-filler (suitable for construction); 5. Polymer clay or salt dough; 6. Thin cotton fabric; 7. Glue (PVA); 8. Varnish spray; 9. Spray paint.

Step 1. Body frame From thicker wire we create the frame of the craft - the basis of the head, neck, torso and tail. At this stage, a simple loop will do just fine as the base of the head. From small pieces of the same thick wire bent in the shape of a “V” tick, we create the front and hind legs, the ends of which we bend into loops (pliers are very useful for this). Using pieces of thin wire we fasten the created paws to the frame of the body, while not skimping on the wire so that the paws are held more firmly. Perhaps this is the most “tedious” part of the whole homemade project.

Next, starting from the back, we begin to create the actual body of the dragon, and we do this with the help of crumpled foil and narrow masking tape. You can directly “press” the foil onto the frame, or form “muscles” out of it and attach them to it with tape. Add foil and tape in layers in the right places until the shape is formed as needed. But we don’t finish the paws, and we don’t overshape the shoulder area, since we still need to attach the wings.

Step 2. Wings It’s easier to make the wings separately first, and only then attach them to the dragon’s body. They, like the paws, are solid. From a piece of wire we bend the two upper “fingers” and forearms of the wings. We make the remaining pairs of “fingers” by bending two pieces of wire in the middle, and then, in the same way as we attached the paws to the body, we fasten them with thin wire.

After this, we begin to wrap foil and tape on the wings. On the “fingers” I used only tape (no foil) to keep them thin. And before forming the “biceps” on the wings, do not forget to attach small pieces of thin wire to them, with which the wings will be attached to the body.

Step 3. Paws Remember those loops we used to mark the paws? Now is the time to form “fingers” on them. To do this, screw two loops of thin wire to each paw and wrap them tightly with tape. Then, by cutting these loops in the middle, we get 4 toes on each paw; they need to be bent, cut to the required length, and given the required shape using foil and tape. If you look closely, you will notice that the tips of such “fingers” are uncovered and protrude like claws. This allows the “dragon” to cling to clothing like a kitten.

Step 4. Head and putty The time has come to tackle the head! Use polymer clay or salt dough to make twisty horns for your dragon (if you want them, of course) and bake them until done. And then using foil and tape we form the dragon's head. Such a head should have brow ridges, a massive lower jaw and a small chin. To do this, we twist short “bundles” of foil and fasten them in the right place. It is advisable to have several pictures of dragons in order to have an idea of what the craft dragon should look like in the end.

The following action is definitely optional, but recommended. The homemade product can be covered with several layers of putty to make the “dragon” smoother and hide wrinkles and folds from the tape. You can also “draw” small details with putty if you know how to do this.

Step 5. Finalizing the wings Using scissors and paper, cut out the wing membranes (roughly), and then transfer this template to a thin cotton fabric, which can be an old sheet or a sample from a fabric store, or something similar.

Step 6. Spikes Typically, dragons have spikes of various shapes, and I'm not even guessing what their evolutionary purpose is, but they do exist. We make spikes of different types and sizes from polymer clay or salt dough, and then bake them. In order to attach these spikes, use a self-tapping screw to “drill” holes in the filler and tape in the right places, dip the spikes in glue and insert them into the holes.

Step 7. Painting and varnishing I painted my homemade product with bronze spray paint in two shades. The belly and spines were painted with white ivory acrylic; for realism, I applied some black acrylic with a dry brush. You can experiment with colors and paint it red or green, whichever you prefer. And after I covered the entire dragon with several layers of spray varnish, I glued on its eyes, which were used as rhinestones.

How to make a plastic fender for a motorcycle YOURSELF | Topic author: Oksana

I'm wondering where they get the plastic for the Jawa 350.

Love Epoxy, fiberglass, old fender and arms.

Alexandra To make fiberglass, you need a matrix - a mold on which you will apply pieces of fiberglass with epoxy. Lubricate the mold with fat, or salidol, wax, plasticine. Then you cut the fiberglass into pieces and stick it onto the mold, then coat it with epoxy - and again a layer of fiberglass. By the way, you can use any fabric and add dyes to the epoxy, for example, a colored pencil lead crushed into powder. Good luck!

Yaroslav Use cellular polycarbonate - it can be bent into any shape under fire. Very durable material

Ivan As I understood the question about how to make a matrix, and only then make a wing based on it. There are two options: one is to find a ready-made wing, and make a matrix out of fiberglass and polyester resin and in subsequent times sculpt the wing inside the matrix, so that the wing has the same dimensions as the standard one. You can also use Polina plasticine or Georgiy plaster plasters as a matrix, from which plaster is applied

Wings on a walk-behind tractor (part 2) – Drive2.ru

mikevazovsky › Blog › Wings on a walk-behind tractor (part 2). And as they say, if you suffer for a long time, the result will be, so I decided to make the wings removable by unscrewing the seven bolts from. Time passed, progress moved, photos were taken).

Homemade products for walk-behind tractors are invented and made by almost all owners of this equipment. The purpose of these actions is to expand the functionality of the unit with minimal financial investment. In the basic configuration, the motor cultivator has extremely limited capabilities. Installing various options on it can turn a small machine into a full-fledged mini-tractor. Often, homemade devices are in no way inferior to factory-made analogues. In order to improve a walk-behind tractor with your own hands, a set of tools that are available in every workshop of a country house or cottage is sufficient. The materials you need can be found at a junkyard, shed, or scrap metal collection point.

Improvement of the chassis

The first thing users of a walk-behind tractor think about is how to make a cart with a seat for it. Using equipment in normal mode using levers requires the application of great physical effort. However, the use of a trailer reduces the stability of the vehicle. This problem can be eliminated by extending the wheelbase. This is done using extensions that are attached to the axle shaft with pins or bolts. Having solved the stability problem, the operator is faced with another issue: the unit is poorly controlled. The differential for the walk-behind tractor helps to give it good maneuverability. This device is made by analogy with components of passenger cars. Homemade unlockers for walk-behind tractors are made using ordinary household tools - an angle grinder, welding and a sharpening machine.

The low weight of the walk-behind tractor causes poor traction between the wheels and the ground. Slipping is a common occurrence when lifting virgin soil, working on wet ground or driving in snow. To avoid slipping, weights are attached to walk-behind tractors.

These devices are divided into the following categories:

Wheeled. They are discs that are mounted on wheels or hubs. Disks are made monolithic from metal, concrete or hollow, filled with sand. The weight of wheel weights can be 30-70 kg.
External. Made from any heavy material (steel, lead, concrete). Attached to the body using hooks or bolts. Some craftsmen weld a frame from a corner to the body. Sandbags, bricks, scrap metal and other heavy objects are placed in it.

You can improve the cross-country ability of a walk-behind tractor by installing lugs. The easiest way to make lugs is to make a rim from a strip of metal and weld blades onto it. The rim diameter should be larger than the rims and smaller than that of the tires. The rim is installed with flat tires. After the lug is installed, the wheel is inflated.

You can improve the transmission by installing a homemade variator on the engine. The system of belts and discs will allow you to smoothly change the speed of the unit, without jerking or vibration.

How to make a trencher for a walk-behind tractor yourself?

Mounted and solid units allow all work to be carried out with maximum efficiency, but some owners want to save money and make such equipment themselves.

A homemade bar for a walk-behind tractor must not only be effective, but also meet the following requirements:

the presence of a cutting system;
well-thought-out power plant;
compliance with the walk-behind tractor with which it will be used;
acceptable weight.

To make equipment you must have the following materials:

Bulgarian;
welding;
dump shovel;
road disc milling machines;
protective covers.

When working on a trencher, it is better to use road milling cutters that are best suited for these types of devices.

To make a homemade device for digging a trench with a walk-behind tractor, you need to follow these steps:

First, the front suspension is created, onto which the digging boom with chain and cutting elements is attached.
You need to place a shovel on the rear suspension so that it reaches the depth of the ditch and clears it of soil.
Install a protective cover that should cover the cutting discs and chain drive.
The equipment is attached to the units using special couplings.

It is important to choose disc cutters that will ensure efficient trench digging. Using trenchers, structurally combined with walk-behind tractors, you can easily carry out the necessary excavation work with virtually no effort required. This saves employee time, money and effort.

The production of mini-tractors and attachments for small equipment helped owners from the private sector shift manual labor to the shoulders of machines.

Attachments on walk-behind tractors for digging trenches are also used by owners of personal plots and landscape designers in cramped environments, when the maneuverability of mechanisms, productivity and low cost of work performed are important.

Reducing noise from the unit

Even the most modern and expensive motor cultivators make a lot of noise during operation, especially at high speeds. This factor greatly tires the operator and can serve as a reason for deterioration of relations with neighbors. A homemade muffler will help solve the problem. This is a task that can be accomplished by any craftsman with basic skills in handling iron.

In order to make a muffler for a walk-behind tractor with your own hands, you will need the following tools and materials:

roulette;
welding machine;
Bulgarian;
electric drill;
hammer;
aluminum clamp;
stainless steel 2 mm thick;
metal shavings.

Having collected everything you need, you can begin to improve the exhaust system.

This is done in the following sequence:

Make 2 oval pipes from stainless steel. The diameter of the pipes should differ by 1-1.5 cm. The pipe joints should be fastened using a welding machine.
In a pipe of smaller diameter, make a maximum number of holes with a diameter of 8 mm. Wrap it with metal shavings. Wrap the shavings with steel wire.
Insert the smaller pipe into the larger one. Fix them in the desired position using steel rods and welding.
Attach the muffler to the exhaust pipe and secure with a clamp.

Making a homemade walk-behind tractor from a motorcycle engine

For normalized operation of the walk-behind tractor, it is necessary to develop a kinematic multi-stage transmission scheme. It allows you to increase the additional ratio, torque and tractive effort. Also, together with the gearbox adapter, the entire circuit provides for the presence of a main gearbox. The most highly efficient engine is obtained by combining the main gear with a geared wheelset.

Thanks to a specialized mechanism, the drive chains are effectively tensioned. This element is attached to the sliders using pins made of steel angles, which, in turn, are able to move freely, stretch, and also weaken the drive chain. A pair of adjusting screws with mounting bolts numbered M10 allows you to perform the above functions.

One of the most complex structures is the main gearbox, made of 10 mm steel plates. Reinforcing disks are located at the mounting bearing location. In order to eliminate the possibility of oil leakage, special continuous welding seams are made. The rear gear wall assumes in its structure the presence of a bracket - a bracket. It is capable of fastening both entire cargo trolleys and agricultural trailers. If you attach the cart to a walk-behind tractor, you will get a real miniature tractor.

The gear cover is made of a five-millimeter steel plate. Thanks to screws number M6, it is freely attached to the body. All straight gear gears are taken from agricultural machines.

Locking the wheels of a walk-behind tractor with a motorcycle engine

An important technical solution regarding the walk-behind tractor is the correct wheel locking. It is imperative to grind the cylindrical neck located on the right half axis next to the splined end. A threaded hole is made on the other axial side. During rotation of the screw number M12, a certain displacement is performed under the action of a cylindrical spring. After the specified moment, the axle shaft moves away from the gears. This is how the wheels are locked.

Motoblock wheels are made from electric car wheels. Sixteen grooves are cut in all disks. Steel plates are welded there. Then jumpers are added, which form the rim of the arable elements.

Plow for walk-behind tractor

The control unit, which allows the plow to freely enter fertile soil, consists of several important parts:

— Welded body type P;

It is into these parts that the direct heel of the plow is inserted. Thanks to technical features, it rotates on a vertical plane, using axial and bushing hinges. The rotation angle is set by the pin number M16. The channel of the particle in question is welded to the rotary heel. (See Do-it-yourself plow for a walk-behind tractor).

Blade for walk-behind tractor

The blade is a necessary device, which is needed at any time of the year. The front blade is used to clear snow, plan terrain, dig holes and move bulk materials. Such equipment for the Neva walk-behind tractor is of good quality, but not everyone can afford it. Do-it-yourself dumps require minimal financial investment. By installing the front blade on the Neva walk-behind tractor, you can solve many household problems. If there are levers and hydraulics, a homemade shovel can also be used as a loader.

To make a blade you will need the following tools:

roulette;
welding machine;
electric drill;
Bulgarian;
spanners;
acrylic paint;
barrel 200 l;
reinforced rubber;
sheet steel 5 mm;
profile pipe 40x20 mm;
paint and brush;
bolts and ties.

Before making a blade, it is necessary to calculate the compliance of the power of the walk-behind tractor with the dimensions of the bucket. Excessive load leads to rapid wear of parts and mechanisms of the unit. Depending on the weight and power of the machine, shovels are made 60-100 cm wide and 20-30 cm high.

Do-it-yourself snow removal for a walk-behind tractor is made in the following sequence:

Applying markings to the barrel, sawing it into 3 equal parts vertically. Cutting 1 piece into strips 5 cm wide.
Fastening 2 workpieces using bitumen and rivets. Aligning the edges of the product. Reinforcement of the bucket with transverse racks.
Fastening strips of tin along the edges of the shovel. This is done by welding or bolts.
Drilling holes for bolts. Attaching a strip of rubber to the bottom of the bucket.
Making a hitch for a shovel. It is made by welding a piece of pipe and a semicircle of sheet metal to the blade. Holes are made on the sector to adjust the angle of attack. A homemade snow removal device is attached to the bracket of the walk-behind tractor with an adapter made of a profile pipe.

The finished product needs to be cleaned and painted. All bolted connections must be lubricated regularly to prevent corrosion.

Types of trenchers

To dig a trench with a walk-behind tractor, you should use an attachment such as a trencher. It is attached to the unit and helps to carry out the required excavation work. These devices are divided into several types, they differ in the method of attachment to the unit and functionality.

Chain mounted trencher

This trenching attachment looks like a giant chainsaw and is designed for digging foundations and large trenches and is ideal for work in rural areas. The equipment is intended for retrofitting mini tractors and is suitable for walk-behind tractors Neva, Oka, Agat and others. It is attached using special couplings and can have different sizes and power.

can have different sizes of booms (earthing devices), due to which trenches of the required volume are dug;
equipped with a variety of cutting chain elements for efficient excavation work;
compact structures can be used near foundations;
the ability to adjust the depth of digging trenches;
possibility of automatic adjustment of chain tension.

Digging equipment

Potato diggers of various types are very popular among farmers. These devices save people from hard manual labor, speeding up the harvesting process several times. The walk-behind tractor has a very simple design. It can be made from metal that remains after the construction and renovation of a house.

To work you will need:

Bulgarian;
welding machine;
electric drill;
heavy hammer;
anvil;
profile steel pipe 20x40 mm;
reinforcement 12 mm;
tin (preferably stainless);
bayonet shovel without handle.

The attachment to the walk-behind tractor is made in a suspended or trailed (modular) design. The hanging tool only digs up the tubers, leaving them lying on the surface for subsequent manual harvesting. A modular potato digger not only extracts the crop from the ground, but also collects it in a mobile container on a chassis.

The manufacture of a digger is carried out in the following sequence:

Drawing up a drawing. The width of the digger should be within 25-30 cm. The angle of attack of the tip is taken perpendicular to the coulter so that the tool does not bury itself in the ground.
The reinforcement is cut into fragments of a given length. Using a hammer and anvil, they are given the required bend.
A container for tubers is assembled from a profile pipe and tin. The chassis or skids are welded to the container frame. The runners are made from pipes, and the chassis is taken from an old stroller, cart or lawn mower.
The holder and reinforcement bars are welded to the shovel. A drawbar is welded to the holder, which is fixed to the assembly container. Connections are made movable using bolts or hinges.
Rust and weld marks are removed. The finished product is treated with an anti-corrosion agent and coated with paint.

Adjustment and adjustment of the digger is carried out using racks and steel ties.

Included with the digger, you can immediately make a disk hiller. This tool will be needed when planting tubers after they have been buried in a trench made by a plow. Hillers are made from old pot lids, profile pipes and bolts. A trolley is assembled from pipes and small wheels, onto which holders for lids are welded at a certain angle. After sharpening on a stone, the discs are mounted on holders.

How to make a caterpillar module for a walk-behind tractor with your own hands?

The cost of materials for making a caterpillar with your own hands is much lower than buying ready-made equipment. Therefore, you can try to assemble it yourself.

This unit usually works by installing an additional pair of wheels and connecting them with a track.

Here are the most common variants of such models:

Production from car tires.

In this case, they all have a fixed width. Often they have to be brought to the desired size manually. This is a labor-intensive procedure. However, the final product is a durable model.

Lugs with straps

This is a very simple option when several grousers are connected with one tape. This design is easy to manufacture, but not reliable enough. Because the connecting tape often breaks.

Chains with steel plates

This is a very cheap version of tracks, and anyone can make them. After all, consumables are almost always at hand.

Conveyor belt and bushing chain with rollers

This option is the most popular. It can be used at any time of the year. This type of tracked module is very simple to manufacture, but the connections are not very reliable.

You should choose an option based on what functions the tracked module will perform and what the power of your walk-behind tractor is.

For small capacities, simple designs can be used; they can withstand standard loads. But for more powerful units, more durable models should be used.

A walk-behind tractor is a universal device for agricultural work. The device is considered universal due to the fact that the design suggests the possibility of its reconstruction. You can make an ATV or a snowmobile with your own hands from a walk-behind tractor. Such conversion does not require significant financial costs or skills, and one machine will perform many functions.

It is advisable to convert a walk-behind tractor into a snowmobile, if only because of the price: the cost of the most primitive machine for moving on snow ranges from 3.5 thousand to 5 thousand dollars. There are also models costing over 10 thousand dollars.

Not everyone can buy a regular snowmobile, so if you urgently need a winter vehicle, you can use a walk-behind tractor. Such homemade products are very popular among rural residents.

Making a field sprayer

A homemade sprayer for a walk-behind tractor is necessary in cases where the area of cultivated crops exceeds 20 acres. Doing this type of work manually is very difficult and can take a whole day. Mechanization of this process will save a lot of time and effort.

To make a sprayer you will need:

welding machine;
Bulgarian;
level;
electric drill;
soldering iron for polypropylene pipes;
profile or round water pipes;
plastic or steel barrel with a capacity of 80-100 l;
wide pneumatic wheels;
plastic pipes;
rubber hose;
injectors or nipples from wheel tubes.

Assembling a homemade sprayer is carried out in the following sequence:

Making the frame. Its dimensions are adjusted to the size of the container. The chassis is attached to the frame. For good cross-country ability you need at least 4 wheels. In the absence of wheels, wide skids are made of aluminum.
The container is installed and secured on the frame. For this purpose, spacers and ties are used. Holes are made in the tank for supplying high-pressure hoses. The tank neck is sealed.
A bracket for the pump is being manufactured. A model is selected that operates from a power take-off shaft (belt drive) or from electricity (motoblock generator).
The irrigation system is being assembled. A durable holder is made from steel profiles. Plastic pipes are attached to it using clamps or plastic ties. A valve is being installed to bleed off excess pressure and injectors.
All parts are connected together, the quality of the fastenings and the tightness of the joints are checked. The tank is filled with water, the unit is tested in various modes, and final adjustments and settings are performed.

A self-made sprayer will fully justify the efforts invested in the first season. Thanks to this device, spraying and watering the garden will be done quickly and efficiently.

Homemade mini bike with a walk-behind engine

I made a homemade mini bike with an engine from a walk-behind tractor, below is a photo and description of the homemade product.

You can make a compact vehicle with your own hands. So, in front of you is a mini bike.

The homemade product reaches a maximum speed of 45 km/h, however, it is better to drive it on smooth asphalt, because there is no suspension.

Let's take a closer look at the design of a homemade mini bike.

The “heart” of the mini bike is an air-cooled gasoline engine with a power of 4 hp. Such motors are usually installed on walk-behind tractors and cultivators, but for other homemade equipment, such an internal combustion engine is quite suitable.

A drive sprocket and a centrifugal clutch were installed on the engine axis.

Gas tank - made from a fire extinguisher and welded directly to the tubular frame.

The wheels are taken from a kart, tread width: front - 128 mm, rear - 130 mm.

The frame and front steering fork are completely homemade, curved and welded from steel pipes.

The steering wheel has throttle and rear brake handles.

Additionally, the author installed a zero-resistance filter, the carburetor remained original from this engine.

The rear driven sprocket is turned on a lathe, and a chain drive is installed. Rear brake, drum, from the Alpha moped.

Also, there are removable footrests.

The homemade product weighs 33 kg, but together with an adult rider, it is capable of quickly picking up speed of more than 40 km/h.

You can make such a homemade mini bike with your own hands. Let's watch a short video review from the author of this homemade product: